Exactly How to Install a Bath Tub: Install an Acrylic Tub and Also Tub Surround
Exactly How to Install a Bath Tub: Install an Acrylic Tub and Also Tub Surround
Blog Article
Are you currently trying to find info about A Step-by-Step Guide to Installing a Bathtub?
Installing a bath tub isn't specifically rocket science, yet it does call for solid plumbing, woodworking, and often, tiling skills. Replacing an old bath tub with a new one is additionally a moderately tough task. If the old tub is conveniently accessible, the project can relocate speedily; if you have to open up a wall to eliminate the old bathtub and position the brand-new bathtub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to move out the old tub and also embeded in the new one. Make certain you have actually qualified yourself for the task and also are comfortable attempting it. Instead of working with a professional to take over a halfway-completed job, it is far better to consider employing one before you start. Opportunities are you might need an expert plumber to make tube links.
This write-up will certainly help you install a new tub in your washroom if you have already purchased a new tub and don't need to change the arrangement of your previous supply of water pipes.
Your tools and material checklist should comprise the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, then the first thing you must do is detach the supply of water. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic due to the limited accessibility that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the staying water that will originate from the pipelines. When the supply pipelines have actually been eliminated, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Prior to proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap and also the other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in place in between the faucet and the sink. Safeguard the tap in position with the producer provided backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous type must be connected to the faucet finishes first, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Mounting the Tub
Using both wood boards under its feet, put the bath tub in the needed placement. The wooden boards are helpful in uniformly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto four tiny points.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the tub till the spirit level reads level.
To mount faucets, fit the bottom of the furthest adaptable faucet adapter to the appropriate supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water and inspect all joints as well as brand-new pipework for leaks and tighten them if needed. Fill up the bath tub and likewise examine the overflow outlet as well as the regular outlet for leaks.
Lastly, deal with the bath paneling as explained in the maker's user's manual. Tiling and sealing around the tub needs to wait until the bathtub has been made use of at the very least when as this will settle it into its last placement.
Preparing for the Installation
First of all, the sustaining structure provided with the bathroom should be fitted (if required) according to the maker's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to ensure that if the faucet comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you utilize all of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its final placement.
Tiling Around the Tub
In the area where the bathroom satisfies the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split a rigid seal, causing the water to permeate the wall in between the bath and also the tiling, causing complications with wetness as well as feasible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components as well as fittings. They are offered in tubes and cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water before securing, to allow for the movement experienced when the bathtub is in usage. The sealant can split fairly early if you do not take into account this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly readily available on the market. It is a good idea to fit the tiles utilizing waterproof or waterproof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen reader about A Step-by-Step Guide to Installing a Bathtub, I imagined sharing that segment was a good idea. Enjoyed our write-up? Please share it. Help others check it out. Thanks a bunch for your time. Please check our blog back soon.
View More
Report this page